0 of 23 Questions completed
Questions:
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
0 of 23 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Which of the following are two methods for terminating Ethernet connectors?
Which of the following terminating Ethernet connectors methods is more widely used?
Jack is troubleshooting an ethernet connection between two buildings. Jack noticed everything was upgraded except the wiring. The network need to support 10Gbps at 500 MHz for a distance of 300 feet using RJ-45 connectors. What type of ethernet cable should the Jack replace the Cat 5 with to meet the connection standard?
Jack is unable to access any network resources. All other users are able to access the network at 100Mbps No IP address, subnet mask or default gateway is displayed on the Jack’s
workstation. The Tom network administrator determinates all connectors are using the correct standard. Upon further investigation the Tom also notices the following:
Wire map results from the Jack patch cable to the patch cable connecting to the switch:
1. Pins 5 and 7 are short
2. The distance is 200ft (61m)
Additional observations on the switch
1. The VLAN is set correctly
2. The port is not disabled
3. The duplex”;speed settings are correct
4. Port LEDs are off for that port.
5. The port is set to untagged.
Which of the following is the MOST likely reason the new employee is having network issues?
Choose what is true about Copper Cable. (Choose all that apply)
Match the correct media connectors types to the correct explanation/definition
Connectors are associated with coaxial media and 10BASE2 networks
|
|
Connectors are small plastic connectors used on telephone cables.
|
|
Connectors are used with twisted-pair cabling, the most prevalent network cable in use today
|
|
Standard for serial transmission, use DB-9 and DB-25
|
|
Match the categories of cables to the to the correct Ethernet Standard.
CAT 5
|
|
CAT 5e (Class D)
|
|
CAT 6 (Class E)
|
|
CAT 6 (Class E)
|
|
CAT 6a (Class Ea)
|
|
CAT 7 (Class F)
|
|
CAT 8/8.1 (Class I)
|
|
CAT 8.2 (Class II)
|
|
Which of the following supports a distance of 100 m/(328 ft)
Which of the following supports a maximum distance of 50 m/(180 ft)?
Which of the following supports a maximum distance of 30 m/(100 ft)?
Tom is installing a new switch in a different location. Tom needs to connect the new switch to the core switch. The core switch is about 300 feet away from the switch and requires only a 100Mbps connection. What type of connection should the technician build for the switch?
Tom is installing a new switch in a different location. Tom needs to connect the new switch to the core switch. The core switch is about 55 meters away from the switch and requires 10Gbps connection over a very short distance. What category of cable should Tom use?
Tom is installing a new PoE(Power over Ethernet) switch in a health care facility. He might also be using it for horizontal cabling to wireless access points. Tom needs to connect the new switch to the core switch. The core switch is about 100 meters away from the switch and requires 10Gbps connection over a very short distance. What category of cable should Tom use?
John has a task to survey an old building and determine the current network infrastructure. Tom test the cable and got a speed of 10 Gbps and max length of 100 meters. He also determines the cable to be well shielded. Based on the Tom’s findings, the cabling meets what specification?
Mary is building a backbone network between two buildings. The average length between the buildings is about 500ft and it must support speeds up to 5Gbps. Which type of Ethernet cabling standard should the Mary use?
A cable engineer chooses to use a fiber cable implementation that uses light emitting diode (LED) technology rather than one that uses lasers. Which type of fiber is the engineer using?
Match the correct transceiver modules
GBIC
|
|
SFP (Small Form Factor Pluggable)
|
|
SFP+ (Enhanced Small Form Factor Pluggable)
|
|
QSFP (Quad Small Form Factor Pluggable)
|
|
QSFP+ (Enhanced Quad Small Form Factor Pluggable)
|
|
You are running fiber optic cable a in a rack with extremely limited space for a connector. What type of fiber optic connector would you most likely use?
A network administrator is building a SAN. The speed requirement is more than 25Gbps, and the distance is about 20 feet. What medium should the network engineer use to build the required link?
A cable technician considering using optical mode OM1 or OM2 cables. The installation specification requires cables that are rated for applications up to 1 Gbps and use LED transmitters. Which of the following should the technician use?
A technician is installing a new fiber connection to a network device in a datacenter. The connection from the device to the switch also traverses a patch panel connection. The chain of connections is in the following order:
The connection is not working. The technician has changed both patch cables with known working patch cables. The device had been tested and was working properly before being installed. Which
of the following is the MOST likely cause of the issue?
A new cabling certification is being requested every time a network technician rebuilds one end of a Cat 6 (vendor-certified) cable to create a crossover connection that is used to connect switches.
Which of the following would address this issue by allowing the use of the original cable?
A technician is installing a cable modem in a SOHO. Which of the following cable types will the technician MOST likely use to connect a modem to the ISP?